Véritable ZF 0730002937 Shim 1.70mm Precision Transmission Spacer ZF Parts Supplier

Véritable ZF 0730002937 Shim 1.70mm | Precision Transmission Spacer | Fournisseur de pièces ZF

‌Présentation du produit‌

Achieve Perfect Transmission Tolerances with Genuine ZF Precision

Ce Véritable ZF 0730002937 Shim is a critical precision component manufactured to an exact thickness of 1.70MM. As an authorized Fournisseur de pièces ZF et Marchand de pièces ZF, we provide this essential OEM shim to ensure your transmission rebuild or repair meets ZF’s rigorous engineering standards for performance and longevity.

Shims are not generic washers; they are precision-calibrated spacers that control end float, set bearing preload, and ensure perfect gear alignment within your ZF gearbox. Using a non-genuine or incorrect shim can lead to premature bearing failure, gear wear, noisy operation, and catastrophic transmission damage. This authentic ZF part guarantees the exact specification required for a perfect rebuild.

Why Choose This Genuine ZF Shim?

• Ingénierie de précision: Manufactured to a critical tolerance of 1.70mm, ensuring perfect axial spacing and bearing preload.

• Optimal Performance: Correct end float is essential for smooth gear operation, power transfer, and longevity of internal components.

• Durabilité: Made from high-strength, hardened steel to withstand the stresses and loads within a transmission.

• Guaranteed Fit: Designed specifically for your ZF transmission model, eliminating guesswork and ensuring a perfect repair.

Spécifications techniques

Compatibilité: This specific shim is used in several modern ZF automatic transmissions. Accurate identification of your transmission model (e.g., ZF 6HP26, ZF 8HP70) is essential before purchase.

Astuce d'installation simple

Warning: Transmission disassembly and shim selection require advanced mechanical knowledge. This is not a typical DIY task. Incorrect shim selection will cause severe damage.

1. Disassembly: Carefully disassemble the transmission to access the component requiring shimming (e.g., differential, planetary gearset, or output shaft).

2. Measurement is Key: The old shim’s thickness is only a starting point. You must measure the actual axial clearance using a dial indicator and then calculate the required shim thickness based on the manufacturer’s specifications. This process is called “selective assembly.”

3. Cleanliness: Ensure the mating surfaces and the bore where the shim sits are perfectly clean and free of any debris or burrs.

4. Install: Place the new genuine ZF 1.70mm shim into its designated location. Ensure it is seated perfectly flat and is not bent or damaged.

5. Reassemble & Verify: Reassemble the components and use a dial indicator to re-check the end float or preload. It must be within the precise range specified by ZF. If it is not, you must disassemble and select a different thickness shim.

6. Final Assembly: Once the clearance is confirmed to be correct, proceed with the full reassembly of the transmission.

Professional Note: Always refer to the official ZF workshop manual for your specific transmission model for the exact measurement procedures and tolerance specifications. Using the correct OEM shim is the only way to ensure a successful repair.

Emballage & Expédition

Par Express : Convient pour une commande d'échantillon ou <50 KG Rapide:3-10 jours Coût d'expédition élevé Service porte à porte
Par avion : Convient à >50 KG Rapide: 3-7 jours Inférieur au coût express Service aéroport à aéroport
Par la mer: Convient à >300 KG Service port à port à moindre coût

En tant que principal fournisseur et revendeur de pièces ZF, nous fournissons des composants d'origine pour maintenir l'intégrité et l'efficacité de votre système de boîte de vitesses. Faites confiance à notre expertise et à notre assurance qualité pour assurer le bon fonctionnement de votre boîte de vitesses ZF.